Description
Montreux is a glass-ceramic mosaic with hexagonal tiles on a white base. The grey-green motifs on them are printed so that diamonds and leaves interlace like a fine technical drawing.
The design is graphic and light, with plenty of free space between the motifs. It suits a Scandinavian bathroom and the wall behind the kitchen worktop, when white and light wood dominate the interior.
What you get
- Model: Montreux, code MOSFBDJ092.
- Shape: hexagonal tiles with a printed pattern, colour range – white pattern with grey-green ornaments.
- Sheet size 300 × 290 mm; 13 sheets are needed to cover 1 m².
- The mosaic is supplied in cartons of 1 m² and sold in multiples of a carton.
Why glass ceramic
- Non-porous: the material absorbs no more than 0.04% water, so it does not go mouldy and does not hold on to odours or stains.
- Lasting colour: it does not fade in the sun (ISO 4892 test) and is not affected by cleaning products (class A under ASTM C650).
- Frost resistance: it withstands freezing and thawing under ASTM C1026, so it is also suitable for exterior surfaces.
- Strength: flexural strength of 55 N/mm² (EN ISO 10545-4), with a smooth, defect-free face.
- Eco-friendly composition: made entirely from recycled glass, with no lead or cadmium pigments or other heavy metals.
Technical specifications
| Parameter | Value |
|---|---|
| Code | MOSFBDJ092 |
| Tile shape | hexagon with a printed pattern |
| Material | glass ceramic, 100% recycled glass |
| Colour and pattern | white pattern with grey-green ornaments |
| Sheet backing | silicone (polyurethane) dots |
| Sheet size | 300 × 290 mm |
| Sheets per 1 m² | 13 |
| Recommended grout joint | 2 mm |
| Flexural strength | 55 N/mm² |
| Water absorption | maximum 0.04% according to EN ISO 10545-3 |
| Frost resistance | yes (ASTM C1026) |
| Chemical resistance | class A (ASTM C650) |
| Quantity per carton | 1 m² |
| Application | bathroom, shower, kitchen, spa and hammam, as well as decorative wall panels |
Silicone backing compared with mesh and paper
The chips of Montreux are fixed to the sheet by small silicone (polyurethane) dots that do not cover their backs. As a result, more than 95% of the rear surface of every chip stays exposed to the adhesive and the bond is stable. The backing adds no thickness and does not disintegrate under the adhesive and grout. In storage the sheet does not warp, and its flexibility lets it follow curved walls, steps and corners.
| Criterion | Silicone dots | Mesh | Paper |
|---|---|---|---|
| Back exposed to the adhesive | over 95% | less, part of the back is covered by the mesh | the whole back, but the paper is on the face |
| View of the chips during installation | chips and joints are visible | chips are visible | hidden under the paper |
| Bending around curves and corners | very easy, the sheet is flexible | easy | difficult, the paper tears |
| After bonding | nothing needs to be removed | nothing needs to be removed | the paper gets wet and tears |
Where to use it
- An accent wall in a bathroom or shower area.
- A decorative kitchen splashback.
- Panels in spa centres, hotels and restaurants.
- Hammams and other wet rooms.
Choosing the grout
White grout preserves the clean look of the surface, while grey-green grout brings the pattern forward. In shower cubicles and other wet areas, choose an epoxy or waterproof C2 grout – it does not let moisture through and does not darken.
Installation steps
- Prepare the substrate: it must be dry, sound, dust-free and level (deviation of up to 2 mm over 2 m). In the shower area, waterproofing is applied first.
- Take a white flexible cement-based adhesive, C2TE S1. Its colour matters – the glass is slightly translucent and a grey adhesive would darken the mosaic.
- Spread the adhesive with a 3–4 mm notched trowel over an area sufficient for 2–3 sheets.
- Press the sheet in and smooth it with a rubber float. Keep the same 2 mm gap between the sheets.
- At corners and around fittings, cut through the silicone dots with a utility knife; individual chips are broken with glass mosaic nippers.
- Grout after 24 hours.
- Remove excess grout with a damp sponge before it dries; epoxy grout residue is cleaned off immediately with a special cleaner.
- Use the shower only after the grout has fully cured.
Have ready beforehand
- white adhesive, class C2TE S1;
- grout – epoxy or C2 with a water-repellent effect;
- two trowels: the notched one (3–4 mm) and the rubber one;
- glass mosaic nippers and a utility knife;
- a bucket, a sponge and clean water.
How much material to calculate
Measure the height and width of each wall, multiply them and add an allowance for cutting – usually 5–10%. The adhesive and grout quantities below are approximate: the adhesive is about 2 kg/m² for chips up to 25 mm in size; for 40 mm chips allow 2.5 kg/m², and for even larger ones 3 kg/m². Grout consumption is calculated as follows: (A + B) / (A × B) × C × D × 1.6 kg/m², where the example is for a chip of about 3 cm, a thickness of about 6 mm and a joint of 2 mm. Actual consumption varies with how level and how absorbent the substrate is, which adhesive and grout you have chosen, how large the trowel is, the width and depth of the joint, and how experienced the installer is. Check against the technical data sheets.
Test results
| Test | Result | Standard |
|---|---|---|
| Water absorption | up to 0.04% | EN ISO 10545-3 |
| Flexural strength | 55 N/mm² | EN ISO 10545-4 |
| Surface | 100% defect-free | EN ISO 10545-2 |
| Effect of chemicals | class A, no change | ASTM C650 |
| Freeze – thaw cycles | withstands | ASTM C1026 |
| Ageing under UV light | no change | ISO 4892 |
| Thermal expansion | withstands | EN ISO 10545 |
Caring for the tiling
- Wipe with a soft cloth or sponge and a neutral cleaning product.
- Do not use abrasive powders, wire brushes or acidic grout cleaners.
- After bathing, go over the surface with a squeegee so that no water marks are left on the glass.
Frequently asked questions
Which adhesive is suitable for Montreux?
White flexible cement-based adhesive, class C2TE S1 – it does not change the colour of the glass.
Which grout should I choose?
For wet areas – epoxy or waterproof. White grout preserves the clean look of the surface, while grey-green grout brings the pattern forward.
Can I order less than one carton?
No, the mosaic is sold in multiples of a 1 m² carton. Take the whole quantity at once so that it all comes from one production batch.
How long does delivery take?
The lead time is up to 20 working days, because the mosaic is ordered specially and arrives in cartons.
Is it suitable for salt water and chlorine?
It is intended for walls and wet rooms; the glass does not react to cleaning products.
Can it be laid over old tiles?
Yes – provided that the old tiling is stable, degreased and primed with a suitable primer.
Colour on screen and in real life
Glass mosaic changes its appearance depending on its surroundings, so the shade on site may differ from the photos and visualisations. The following all have an influence:
- the brightness and type of the screen of your phone, tablet or monitor;
- the lighting – sunny or overcast, lamps, morning or evening;
- the viewing angle, because glass reflects light differently;
- the water in the pool – with great depth, clear water and a reflected sky the shade becomes richer and bluer;
- the grout, the adhesive and the size of the area covered;
- the plants, walls, paving and coping around it;
- the batch it was made from – slight variations in shade are possible from one batch to another;
- natural differences between chips in mixes and glass with special effects.
The pool and interior visualisations shown are indicative. If the exact colour is decisive, ask for a consultation before ordering. Send us the dimensions of the room or the pool and we will calculate the square metres and the number of cartons.
See also: Wellness, Pools and Equipment, Cladding and Paving, Pools, Pool Chemicals, Pool Accessories.
